151 Which type of fit represent the tolerance zone of the hole and shaft over lap each other? | किस प्रकार का फिट एक दूसरे पर छेद और शाफ्ट के सहिष्णुता क्षेत्र का प्रतिनिधित्व करता है?
A: Transition fit | संक्रमण फिट
B: Clearance fit । क्लीयरेंस फिट
C: Shrinkage fit | संकोचन फिट
D: Interference fit | हस्तक्षेप फिट
152: How to hold the small jobs while working on bench grinder? | बेंच ग्राइंडर पर काम करते समय छोटी नौकरियां कैसे पकड़ें?
A: Hold the job with cotton waste | कपास के कचरे के साथ काम पकड़ो
B: Hold the job with gloves | दस्ताने के साथ काम पकड़ो
C: Hold the job with pliers | सरौता के साथ काम पकड़ो
D: Hold the job with hand | काम को हाथ से पकड़ें
153 : What type of operation carried out on grinding wheel? | पीस व्हील पर किस प्रकार का ऑपरेशन किया गया?
A : Glazing | ग्लेज़िंग
B : Loading | लोडिंग
C: Dressing | ड्रेसिंग
D : Pinning | पिनिंग
154 What is the recommended gap between tool post and grinding wheel? | टूल पोस्ट और पीस व्हील के बीच अनुशंसित अंतर क्या है?
A: 1 mm
B: 2 mm
C: 3 mm
D: 4 mm
155: What is the pitch of wave set in hexablade ? । तरंग सेट हैकसॉ ब्लेड की पिच क्या है?
A 0.4 mm
B: 0.8 mm
C: 1.2 mm
D: Over 1.0 mm
156 Which drilling machine is used to drill holes between 6mm to 12 mm? | 6 मिमी से 12 मिमी के बीच छेद ड्रिल करने के लिए किस ड्रिलिंग मशीन का उपयोग किया जाता है?
A : Breast drill | ब्रेस्ट ड्रिल
B: Ratchet hand drill | रेचट हैण्ड ड्रिल
C : Pneumatic hand drill | प्रयूमटिक हैण्ड ड्रिल
D: Electric hand drill light duty | इलेक्ट्रिक हैंड ड्रिल लाइट ड्यूटी
157 What are the tools are used to remove the drills and sockets from the machine spindle? | मशीन स्पिंडल से ड्रिल और सॉकेट निकालने के लिए कौन से टूल का उपयोग किया जाता है?
A: Screw driver and hammer | स्क्रू ड्राइवर और हथौड़ा
B: Spanner and hammer | स्पैनर और हथौड़ा
C Punch and hammer | पंच और हथौड़ा
D: Drift and hammer | ड्रिफ्ट और हथौड़ा
158: Which angle helps in the penetration of the cutting edges in the material? | सामग्री में काटने के किनारों के प्रवेश में कौन सा कोण मदद करता है?
A: Helix angle | हेलिक्स कोण
B: Point angle | B बिंदु कोण
C: Clearance angle | क्लीयरेंस कोण
D: Rake angle | रेक कोण
159 : Which tap in a set have 20° chamfer at its end? । एक सेट में किस नल के अंत में 20° चम्फर होता है?
A: Intermediate tap | इंटरमीडिएट टेप
B: Taper tap | टेपर टैप
C: Plug tap | प्लग टैप
D: Second tap | सेकंड कट
160 Why alternate teeth are staggered in hacksaw blade? | क्यों वैकल्पिक दांत हैकसॉ ब्लेड में कंपित होते हैं?
A: For free cutting action | मुफ्त काटने की कार्रवाई के लिए
B: For curve cutting action | वक्र काटने की क्रिया के लिए
C: For coarse cutting action | मोटे काटने की कार्रवाई के लिए
D: For straight cutting action | सीधे काटने की क्रिया के लिए
161: Which material resist the flow of electron? । कौन सा पदार्थ इलेक्ट्रॉन के प्रवाह का विरोध करता है?
A : Gold | सोना
B : Glass | कांच
C : Silver | चांदी
D : Copper | तांबा
162: Which is measured by ammeter in an electrical circuit? | विद्युत सर्किट में एमीटर द्वारा मापा जाता है?
A : Power | शक्ति
B : Voltage | वोल्टेज
C : Current | करंट
D: Resistances | प्रतिरोधों
163 What is the unit of capacitance? | कैपसिटेन्श की इकाई क्या है?
A : Ohm | ओम
B : voltage | वोल्टेज
C : farad | फेरड
D:ampere | एम्पेयर
164: What is the name of the apparatus? | उपकरण का नाम क्या है?
A : Hydrometer | हाइड्रोमीटर
B: Thermometer | थर्मामीटर
C: Lactometer | लाकटोमिटेर
D : Barometer | बैरोमीटर
165: Name the logic gate shown in figure? | फिगर में दिखाए गए लॉजिक गेट का नाम बताएं?
A: AND gate | एंड गेट
B : OR gate | आर गेट
C: NOT gate | नॉट गेट
D: NAND gate | नन्द गेट