Electrician 1 st sem – NSQF – Module 2 – Basic Workshop Practice (Allied trade) MOCK TEST

by

TRANSLATE THIS QUIZ IN YOUR LANGUAGE

इस प्रश्नोत्तरी का अपनी भाषा में अनुवाद करें

 0%

Question 1 of 33

1. What is the use of mortise chisel?

Rate this question:

Question 1 of 33

Question 2 of 33

2. What is the use of firmer chisel?

Rate this question:

Question 2 of 33

Question 3 of 33

3. Which type of stake is used for riveting or seaming tapered cone shaped articles?

Rate this question:

Question 3 of 33

Question 4 of 33

4. What is the name of the stake used for sheet metal work?

Rate this question:

Question 4 of 33

Question 5 of 33

5. What is the name of the tool?

Rate this question:

Question 5 of 33

Question 6 of 33

6. What is the name of tool?

Rate this question:

Question 6 of 33

Question 7 of 33

7. What is the name of the hammer?

Rate this question:

Question 7 of 33

Question 8 of 33

8. Which type of chisel is used for separating metals after chain drilling?

Rate this question:

Question 8 of 33

Question 9 of 33

9. Which file is used for sharpening the blunt teeth of a tenon saw?

Rate this question:

Question 9 of 33

Question 10 of 33

10. What defect will occur in timber due to irregularity in growth of the branches?

Rate this question:

Question 10 of 33

Question 11 of 33

11. Which type of caliper is used to draw parallel lines along the outer edges of the materials?

Rate this question:

Question 11 of 33

Question 12 of 33

12. Which type of half lap joint is used if one part of a job meets another part at some distance from the ends?

Rate this question:

Question 12 of 33

Question 13 of 33

13. What is the name of the file?

Rate this question:

Question 13 of 33

Question 14 of 33

14. Which defect in timber is caused due to improper seasoning?

Rate this question:

Question 14 of 33

Question 15 of 33

15. Which type of curve cutting hand saw is used for internal cutting in wood?

Rate this question:

Question 15 of 33

Question 16 of 33

16. What is the use of this gauge?

Rate this question:

Question 16 of 33

Question 17 of 33

17. What is the name of the formation of thread marked as 'X' in the galvanized sheet pipe joint?

Rate this question:

Question 17 of 33

Question 18 of 33

18. What is the name of the tool?

Rate this question:

Question 18 of 33

Question 19 of 33

19. What is the name of the stake used for general purpose in sheet metal work?

Rate this question:

Question 19 of 33

Question 20 of 33

20. What is the purpose of hem folding in sheet metal work?

Rate this question:

Question 20 of 33

Question 21 of 33

21. Name the part marked 'X' of the file.

Rate this question:

Question 21 of 33

Question 22 of 33

22. Which cause knot defect in timbers?

Rate this question:

Question 22 of 33

Question 23 of 33

23. What is the name of the angle marked 'X' of the chisel?

Rate this question:

Question 23 of 33

Question 24 of 33

24. Which type of notch is used for bending the edge of the sheet?

Rate this question:

Question 24 of 33

Question 25 of 33

25. Which type of cold chisel is used for squaring materials at the corners?

Rate this question:

Question 25 of 33

Question 26 of 33

26. Which type of stake is used for sharp bends in sheet metal?

Rate this question:

Question 26 of 33

Question 27 of 33

27. What is the name of the drill bit?

Rate this question:

Question 27 of 33

Question 28 of 33

28. What is the cause for twisting defect in timber?

Rate this question:

Question 28 of 33

Question 29 of 33

29. Which type of notch is used to make a job with 90° bend?

Rate this question:

Question 29 of 33

Question 30 of 33

30. Which type of notch is used for making a metal tray with 90° bend and an inside flange?

Rate this question:

Question 30 of 33

Question 31 of 33

31. What is the purpose of cross cut cold chisel?

Rate this question:

Question 31 of 33

Question 32 of 33

32. Which defect in the timber is caused to reduce its strength?

Rate this question:

Question 32 of 33

Question 33 of 33

33. What is the number 1.25 indicates in ISO metric fine thread M12 x 1.25?

Rate this question:

Question 33 of 33


 

2 thoughts on “Electrician 1 st sem – NSQF – Module 2 – Basic Workshop Practice (Allied trade) MOCK TEST”

Leave a Reply to Vyaspatel Cancel reply

Translate »
error: Content is protected !!