Wireman – Semester 1 Module 6: Basic Workshop Practice
126 : What is the name of the hammer?
A : Claw hammer
B : Straight pein hammer
C : Ball pein hammer
D : Cross pein hammer
127 : What is the size of firmer chisel?
A : 1 mm to 30 mm
B : 2 mm to 40 mm
C : 3 mm to 50 mm
D : 4 mm to 60 mm
128 : How files are specified?
A : By length
B : By thickness
C : By width
D : By total length with handle
129 : What is the use of cross cut chisel?
A : Cutting keyways
B : Cutting curved grooves
C : Squaring materials at corners
D : Removing metal after chain drilling
130 : What purpose rough file is used?
A : High degree finishing
B : Good finishing purpose
C : Removing less metal and good finish
D : Removing more quantity of metal quickly
131 : What is the name of hacksaw frame part marked as X ?
A : Handle
B : Frame
C : Fixed blade holder
D : Frame length adjustment
132 : How hacksaw blades are specified?
A : Teeth per 10mm
B : Teeth per 15mm
C : Teeth per 20mm
D : Teeth per 25mm
133 : What is the use of fret saw?
A : Larger curve cutting
B : Cutting sharp corners
C : Internal cutting
D : Cutting sharp and fine curves
134 : What is the name of the tool?
A : ‘G clamp
B : Vice clamp
C : Bench hook
D : Carpenters vice
135 : What is the accuracy of the wooden folding rule?
A : 0.05 mm
B : 0.25 mm
C : 0.5 mm
D : 1 mm
136 : How nails are specified?
A : By length only
B : By type only
C : By length and type only
D : By length type and gauge number
137 : What is the use of the carpenter tool?
A : Marking lines parallel to face
B : Marking holes on wood
C : Check the thickness of wood
D : Check the squareness of wood
138 : Which is the name of wooden joint?
A : End lap joint
B : Middle lap joint
C : Cross lap joint
D : Corner joint
139 : Which defect in timber is caused by the growth of branches?
A : Twisting
B : Cracking
C : Cupping
D : Knot
140 : What is the name of the drilling machine?
A : Pillar drilling machine
B : Radial drilling machine
C : Electric hand drilling machine
D : Sensitive bench drilling machine
141 : Which formula is used to calculate cutting speed (CS) of a drill bit of d = dia of drill, N = spindle speed in RPM?
142 : Which speed can be achieved by the belt arrangement in bench drilling machine?
A : 2 times below than rated speed
B : 3 times below than rated speed
C : Rated speed
D : Above rated speed
143 : What is the name of the operation needed to enable the head of the screw to fit flush with the surface of a component?
A : Drilling
B : Tapping
C : Reaming
D : Counter sinking
144 : What is the indication of the letter ‘M’ in thread formation M12?
A : BSF thread
B : BSW thread
C : ISO inch thread
D : ISO metric thread
145 : What is the thread angle of British standard worth (BSW) thread?
A : 60°
B : 65°
C : 55°
D : 50°
146 : How many types of threaded fastening available in ISO inch (unified) thread?
A : One
B : Two
C : Four
D : Three
147 : What is the use of stock and die sets?
A : To make internal threads in cylindrical jobs
B : To make external threads in cylindrical jobs
C : To make internal threads in square jobs
D : To make external threads in square jobs
148 : Which is the name of wrench?
A : T-handle tap wrench
B : Double-ended non-adjustable tap wrench
C : Solid tap wrench
D : Double ended adjustable tap wrench
149 : What is the effect on thread is the side screw in more tighted?
A : No effect threads form normally
B : Threads forms unevenly
C : Both die and threads damaged
D : Pipe broken into pieces
150 : What is the name of the stake?
A : Square stake
B : Hatchet stake
C : Blow-horn stake
D : Bevel-edge square stake
151 : What is the name of the tool?
A : Stakes
B : “C” clamps
C : Folding bar
D : Angle steel
152 : What is the cutting angle of “V” notch marked as X ?
A : 30° angle to the edge of the sheet
B : 40°angle to the edge of the sheet
C : 45° angle to the edge of the sheet
D : 50° angle to the edge of the sheet
153 : What is the use of bent snips?
A : To cut straight slot
B : To cut internal holes
C : To cut external curves
D : To cut internal curves
154 : Which notch is used, if a single hem meets at right angles?
A : ‘V notch
B : Slant notch
C : Square notch
D : Straight notch
155 : Which type of notch is used for forming rectangular box?
A : ‘V notch
B : Slant notch
C : Square notch
D : Straight notch
156 : What is the name of the part marked as X in an universal surface gauge?
A : Snug
B : Scriber
C : Spindle
D : Clamping Nut
157 : What is the name of the gauge?
A : Limit gauge
B : Radius gauge
C : Thread ring gauge
D : Standard wire gauge
158 : How to check the radius of the parts by using radius gauge?
A : Comparing with radius of the radius gauge
B : Actual measuring with the help of radius gauge
C : Calculated with the help of the radius gauge
D : Visually displayed in radius gauge
159 : What is the name of the tool?
A : Bent snip
B : Straight snip
C : Side cutting plier
D : Diagonal cutting plier
160 : Which is called as plate?
A : Sheets over 2 mm thick
B : Sheets over 3 mm thick
C : Sheets over 4 mm thick
D : Sheets over 5 mm thick
161 : Which type of stakes are used for riveting cone shape articles?
A : Square stake
B : Hatchet stake
C : Bevel edge square stake
D : Blow horn stake
162 : Which makes the edge smooth and stiff in small sheet metal aritcals?
A : Slant notch
B : Single hem
C : Double hem
D : Square notch