WIREMAN 1st Year NSQF Mock Test – Module Industrial Wiring Practice June 13, 2026July 15, 2025 by admin <<1234567891011121314151617181920212223242526272829303132333435>> 0% Question 1 of 35 What is name of part marked as 'x'? ('एक्स' के रूप में चिह्नित भाग का नाम क्या है?): Porcelain supports (पोर्सिलेन सपोर्ट्स) Bus-bars (बस बार) Cable entry hole (केबल एंट्री होल) Enclosure (इन्क्लोजर)Rate this question: Loading... Question 1 of 35Question 2 of 35 What is the recommended resistance value of earth continuity conductor used in domestic wiring installation as per IE Rules? (IE नियम के अनुसार घरेलू वायरिंग इंस्टॉलेशन में पृथ्वी निरंतरता कंडक्टर के अनुशंसित प्रतिरोध मूल्य को क्या कहा जाता है?): Not more than 1 ohm (1 ओम से अधिक नहीं) Not more than 8 ohm (8 ओम से अधिक नहीं) Not more than 3 ohm (3 ओम से अधिक नहीं) Not more than 2 ohm (2 ओम से अधिक नहीं)Rate this question: Loading... Question 2 of 35Question 3 of 35 Why over load relay coil is wound with thick gauge of copper wire? (ओवर लोड रिले कॉइल तांबे के तार के मोटे गेज से वाउंड करके क्यों बनाई है?): To reduce the power loss (बिजली के नुकसान को कम करने के लिए) To reduce voltage drop (वोल्टेज ड्रॉप कम करने के लिए) To carry the line voltage (लाइन वोल्टेज ले जाने के लिए) To carry load current (लोड करंट ले जाने के लिए)Rate this question: Loading... Question 3 of 35Question 4 of 35 How many sections of wiring are there in industrial wiring? (औद्योगिक मोटर वायरिंग में वायरिंग के कितने भाग होते हैं?): 4 2 1 3Rate this question: Loading... Question 4 of 35Question 5 of 35 What is the minimum clearance required between the wall and backside of a panel board in industrial wiring? (औद्योगिक वायरिंग में एक पैनल बोर्ड के पीछे और दीवार के बीच न्यूनतम निकासी क्या होगी?): Not less than 18.4 cm (18.4 सेमी से कम नहीं) Not less than 22.88 cm (22.88 सेमी से कम नहीं) Not less than 15.8 cm (15.8 सेमी से कम नहीं) Not less than 10.2 cm (10.2 सेमी से कम नहीं)Rate this question: Loading... Question 5 of 35Question 6 of 35 Why the equipment are arranged in front side of the switch board in industrial wiring? (औद्योगिक वायरिंग में स्विच बोर्ड के सामने उपकरणों की व्यवस्था क्यों की जाती है?): To test the supply frequently (आपूर्ति का बार-बार परीक्षण करने के लिए) To operate easily (आसानी से संचालित करने के लिए) To avoid personal contacts during maintenance (रखरखाव के दौरान व्यक्तिगत संपर्क से बचने के लिए) To avoid short circuit (शॉर्ट सर्किट से बचने के लिए)Rate this question: Loading... Question 6 of 35Question 7 of 35 Which is the unit of insulation resistance? (इंसुलेशन प्रतिरोध की इकाई कौन सी है?): Mega ohm (मेगा ओम) Ohm (ओम) kilo ohm (किलो ओम) Milli ohm (मिली ओम)Rate this question: Loading... Question 7 of 35Question 8 of 35 How the cable size is determined for industrial wiring? (औद्योगिक वायरिंग के लिए केबल आकार कैसे निर्धारित करेगे?): By considering the power factor (पावर फैक्टर पर विचार करके) By considering the voltage of circuit (सर्किट के वोल्टेज पर विचार करके) By considering the current carrying capacity of the cable (केबल का करंट ले जाने की क्षमता पर विचार करके) By considering the load resistance (भार प्रतिरोध पर विचार करके)Rate this question: Loading... Question 8 of 35Question 9 of 35 Which wiring is preferred for motor connection in industries? (उद्योगों में मोटर कनेक्शन के लिए कौन सी वायरिंग पसंद की जाती है?): CTS wiring (सी टी एस वायरिंग) PVC conduit wiring (पी वी सी कंडूट वायरिंग) Metal conduit wiring (मेटल कंडूट वायरिंग) TRS wiring (टी आर एस वायरिंग)Rate this question: Loading... Question 9 of 35Question 10 of 35 Which is the purpose of single phasing preventor in 3 phase motor circuit? (3 फेज मोटर सर्किट में सिंगल फेजिंग प्रिवेंटर का उद्देश्य क्या है?): To regulate the supply voltage (आपूर्ति वोल्टेज विनियमित करने के लिए) To run the motor continuously at single phasing (सिंगल फेजिंग पर लगातार मोटर चलाने के लिए) To protect the motor from damage (नुकसान से मोटर की सुरक्षा के लिए) To protect the motor from over load (अधिक लोड से मोटर की सुरक्षा के लिए)Rate this question: Loading... Question 10 of 35Question 11 of 35 What is the alpha numeric notation of 3 phase apparatus connection? (3 फेज सिस्टम कनेक्शन के अल्फा न्यूमेरिक अंकन क्या है?): U, V, W & N R, Y, B & N A1,B1, C1 & N L1, L2, L3 & NRate this question: Loading... Question 11 of 35Question 12 of 35 Which factor determines the size of wire to be used for industrial motor wiring? (औद्योगिक मोटर वायरिंग के लिए किस कारक का उपयोग तार के आकार को निर्धारित करता है?): Type of motor (मोटर के प्रकार) Load current (लोड करंट) Supply voltage (सप्लाई वोल्टेज) Purpose of motor (मोटर का उद्देश्य)Rate this question: Loading... Question 12 of 35Question 13 of 35 What is the purpose of openings provided in bus bar chamber? (बस बार चैम्बर में होल दिए जाने का उद्देश्य क्या है?): To release the heat (गर्मी निकलने के लिए) For cable entries (केबल प्रविष्टियों के लिए) To extend the busbar (बस बार विस्तार करने के लिए) For air circulation (हवा परिसंचरण के लिए)Rate this question: Loading... Question 13 of 35Question 14 of 35 Which material is used to make busbars? (कौन सा सामग्री बसबार बनाने के लिए प्रयोग किया जाता है?): Aluminium (एल्युमीनियम) Bronze (कांसा) Galvanised iron (गैल्वेनाइज्ड आयरन) Brass (पीतल)Rate this question: Loading... Question 14 of 35Question 15 of 35 Which is the name of relay marked as 'x'? (रिले का नाम 'x' के रूप में क्या है?): Electromagnetic relay (इलेक्ट्रोमैग्नेटिक रिले) Over voltage relay (ओवर वोल्टेज रिले) Under voltage relay (अंडर वोल्टेज रिले) Time delay relay (टाइम डिले रिले)Rate this question: Loading... Question 15 of 35Question 16 of 35 What is the thickness of steel sheet used for the covers of bus bar chamber? (बस बार चैम्बर के कवर में उपयोग की गई स्टील शीट की मोटाई क्या है?): 1.5 mm (1.5 मिमी) 2.5 mm (2.5 मिमी) 1 mm (1 मिमी) 2 mm (2 मिमी)Rate this question: Loading... Question 16 of 35Question 17 of 35 What is the colour code of single phase AC supply as per NE code? (NE कोड के अनुसार सिंगल फेज एसी सप्लाई का रंग कोड क्या है?): Red and blue (लाल और नीला) Red and yellow (लाल और पीला) Red and black (लाल और काला) Red and green (लाल और हरा)Rate this question: Loading... Question 17 of 35Question 18 of 35 Which is the part name marked as 'x' starter face plate arrangement? (स्टार्टर फेस प्लेट अरेंजमेंट में 'X' के रूप में किस भाग का नाम है?): Over load relay (ओवर लोड रिले) Spiral spring (स्पाइरल स्प्रिंग) No volt coil (नो वोल्ट कॉइल) Studs (स्टड्स)Rate this question: Loading... Question 18 of 35Question 19 of 35 Which place the control ON/OFF switches is to be placed in industrial motor wiring? (औद्योगिक मोटर वायरिंग लगाने के लिए कंट्रोल ऑन/ऑफ स्विच को किस स्थान पर रखा गया है?): Near the entrance (प्रवेश द्वार के पास) Near the motor (मोटर के पास) Near the control panel (नियंत्रण कक्ष के पास) Near the input main (इनपुट मेन के पास)Rate this question: Loading... Question 19 of 35Question 20 of 35 How many earth is to be provided for a AC 3 phase induction motor? (एक एसी 3 फेज इंडक्शन मोटर के लिए कितने अर्थ प्रदान किए जाते हैं?): 2 1 3 4Rate this question: Loading... Question 20 of 35Question 21 of 35 How to reduce the earth resistance value keep as low? (अर्थ प्रतिरोध के मान को कैसे कम किया जाता है?): By adding more charcoal (अधिक चारकोल जोड़कर) By connecting two earth in series (श्रृंखला में दो अर्थ कनेक्ट करके) By adding more salt (अधिक नमक जोड़कर) By connecting to earth in parallel (समानांतर में अर्थ से कनेक्ट करके)Rate this question: Loading... Question 21 of 35Question 22 of 35 Which is the purpose of control wiring? (कंट्रोल वायरिंग का उद्देश्य क्या है?): To increase the motor input voltage (मोटर इनपुट वोल्टेज बढ़ाने के लिए) To limit the load current (लोड करंट सीमित करने के लिए) To measure the load current (लोड करंट को मापने के लिए) To communicate the commands to control devices (उपकरणों को नियंत्रित करने के लिए कमांड संचारित करना)Rate this question: Loading... Question 22 of 35Question 23 of 35 What is the formula to calculate the standard value of Insulation Resistance (Ri) as per BIS? (बी आई एस के अनुसार इंसुलेशन प्रतिरोध (Ri) के मानक मूल्य की गणना करने का सूत्र क्या है?): CADBRate this question: Loading... Question 23 of 35Question 24 of 35 What is the formula to calculate the value of insulation resistance while testing the wiring? (तारों का परीक्षण करते समय इंसुलेशन प्रतिरोध के मान की गणना करने का सूत्र क्या है?): DCBARate this question: Loading... Question 24 of 35Question 25 of 35 Why power and control wiring is to be run in a separate conduit in industrial motor wiring? (पावर और कंट्रोल वायरिंग को औद्योगिक मोटर वायरिंग में एक अलग पाइप में क्यों चलाया जाता है?): For easy identification (आसान पहचान के लिए) For easy maintenance (आसान रखरखाव के लिए) To reduce the voltage drop (वोल्टेज ड्रॉप कम करने के लिए) To avoid current radiation (करंट विकिरण से बचने के लिए)Rate this question: Loading... Question 25 of 35Question 26 of 35 What is the main reason for leakage current flowing in wiring installation? (वायरिंग इंस्टॉलेशन में लीकेज करंट प्रवाहित होने का मुख्य कारण क्या है?): Insulation failure (इंसुलेशन विफलता) Incorrect size of earth wire (अर्थ वायर की गलत साइज) High earth reactance (हाई अर्थ रिएक्टेंस) Low earth resistance (लो अर्थ रेसिस्टेंस)Rate this question: Loading... Question 26 of 35Question 27 of 35 What is the colour code of 3 phase 4 wire AC supply system? (3 फेज 4 तार एसी सप्लाई सिस्टम के रंग कोड क्या है?): Red, black, green, blue (लाल, काले, हरे, नीले) Red, yellow, blue, black (लाल, पीले, नीले, काले) Red, blue, black, yellow (लाल, नीले, काले, पीले) Red, yellow, black, green (लाल, पीले, काले, हरे)Rate this question: Loading... Question 27 of 35Question 28 of 35 How many earth continuity conductors should be provided from the machine to panel board and to the main earth electrode? (मशीन से पैनल बोर्ड और मुख्य अर्थ इलेक्ट्रोड को कितने अर्थ कंटीन्यूटी कंडक्टर प्रदान किए जाने चाहिए?): 1 2 3 4Rate this question: Loading... Question 28 of 35Question 29 of 35 Which instrument is used to measure the insulation resistance? (कौन सा उपकरण इंसुलेशन प्रतिरोध को मापने के लिए प्रयोग किया जाता है?): Shunt type ohmmeter (शंट टाइप ओम मीटर) Multimeter (मल्टीमीटर) Series type ohmmeter (सीरीज टाइप ओम मीटर) Megger (मेगर)Rate this question: Loading... Question 29 of 35Question 30 of 35 Which size of GI conductor is used for earthing to the motor from the main electrode? (मुख्य इलेक्ट्रोड से मोटर के लिए अर्थिंग के लिए जीआई कंडक्टर के किस आकार का उपयोग किया जाता है?): 14 SWG 10 SWG 8 SWG 4 SWGRate this question: Loading... Question 30 of 35Question 31 of 35 Which rated voltage megger is used to measure the insulation resistance value of 3phase 415V induction motor? (3फेज 415V प्रेरण मोटर के इंसुलेशन प्रतिरोध मूल्य को मापने के लिए किस रेटेड वोल्टेज मेगर का उपयोग किया जाता है?): 500V 2500V 250V 1000VRate this question: Loading... Question 31 of 35Question 32 of 35 What is the minimum distance in front of the switch board for industrial panel board wiring? (औद्योगिक पैनल बोर्ड वायरिंग के लिए स्विच बोर्ड के सामने की न्यूनतम दूरी क्या है?): 1.5 M 1 M 2 M 0.5 MRate this question: Loading... Question 32 of 35Question 33 of 35 What is the colour code of protective earthing conductor as per NE code? (NE कोड के अनुसार सुरक्षात्मक अर्थिंग कंडक्टर का रंग कोड क्या है?): Green (हरा) Black (काला) Red (लाल) Blue (नीला)Rate this question: Loading... Question 33 of 35Question 34 of 35 Which is the name of starter? (कौन से स्टार्टर का नाम है?): MINI manual starter (मिनी मैनुअल स्टार्टर) D.O.L starter (डी ओ एल स्टार्टर) Manual star delta starter (मैनुअल स्टार डेल्टा स्टार्टर) Auto star delta starter (ऑटो स्टार डेल्टा स्टार्टर)Rate this question: Loading... Question 34 of 35Question 35 of 35 Which material is used for harnessing of cable? (केबल के दोहन के लिए किस सामग्री का उपयोग किया जाता है?): Metal bands (मेटल बैंड) Link clips (लिंक क्लिप) P.V.C sleeves (P.V.C स्लीव्स) P.V.C saddles (P.V.C सैडल)Rate this question: Loading... Question 35 of 35 Loading...